NovaSolver for teaching
Use physics and engineering simulators that run in the browser for explanations, exercises and homework. No sign-up, no install: they open on students' PCs, tablets and phones.
Three ways to use them
Share a link
When you set values in a tool, they are written into the address bar after the "#". Paste that URL into Google Classroom, Moodle or any LMS assignment and students start from the same setup.
Embed it
Paste the URL into the box below to get an embed code (iframe) that opens with those values. It works in Google Sites, Moodle pages, WordPress and similar.
Show it in class
Project it, ask students to predict, then move the values. The questions below are examples for that predict-then-check routine.
Make an embed code
| Google Classroom | Embedding is not supported; add the URL to an assignment or material as a link. |
|---|---|
| Google Sites | Insert → Embed → Embed code, then paste. |
| Moodle | Switch the page or label editor to HTML (source) view and paste. If your site does not allow iframes, share the link instead. |
| WordPress | Paste into a Custom HTML block. |
An embedded tool shows only its controls and plots, with a link back to the full page underneath. Use and embedding are free for schools and universities.
Tools and discussion questions by area
Mostly tools that teachers already use. Each question is meant to be answered as a prediction before the values are changed.
Mechanics and mechanisms
A 20-tooth gear drives a 60-tooth gear. By what factor do speed and torque change? Without losses, how do input and output power compare?
With air resistance off and the same launch speed, which angle gives the longest range? Compare 30° and 60°. With air resistance on, which way does the best angle move?
With the crank turning at constant speed, is the piston fastest exactly at 90° of crank angle? What changes with a longer connecting rod?
Run it twice with a tiny change in the starting angle. How long do the two runs stay together, and when do they part?
Keep the same point load at mid-span of a simply supported beam and double the span. By what factor does the mid-span deflection grow?
Fluids
Make the outlet diameter about 0.71 of the inlet (half the area). What happens to the outlet speed and pressure?
The differential pressure reading becomes four times larger. By what factor has the flow rate changed?
Same water, same speed, but a pipe ten times wider. How do the Reynolds number and the flow regime change?
Increase the angle of attack step by step from 0°. How does the lift coefficient change? What does the thickness change?
At 0° angle of attack, how does the symmetric NACA 0012 compare with the cambered 2412? What is the camber doing?
Heat
Switch the material from copper to concrete. How much longer before the middle starts to warm up? Compare with the thermal diffusivities.
Heat only one edge of the plate. What shape do the isotherms inside take?
What is the dew point of air at 25 °C and 60 % relative humidity? Use it to explain why a glass with a cold drink gets wet outside.
How does the boiling temperature of water change with pressure? Find the temperature inside a pressure cooker.
At the same air temperature, how do air speed and clothing change how warm or cold it feels (PMV)?
Waves, vibration and light
Double the frequency. How does the pitch sound?
Play 440 Hz and 444 Hz together. How many beats per second do you hear?
Reduce the damping. What happens to the height and width of the resonance peak?
Place the object inside the focal length of a convex lens. Where is the image, which way up, and how large?
Circuits, control and signals
Make the inductance four times larger. By what factor does the resonant frequency change?
Disable the integral action and raise only the proportional gain. How do rise time and overshoot change? Turn the integral back on: what happens to the error left at the end?
Build a square wave from sine waves. Does the overshoot near the corners disappear as you add terms?
Sample slower than twice the signal frequency. What does the wave through the sample points look like?
Materials and structures
Double the column length. By what factor does the buckling load change?
How many degrees apart are the principal planes and the planes of maximum shear stress?
Lower the stress amplitude a little. How much longer does the part last?
With the same number of members, how does a layout made of triangles fail compared with one without them?
Find other tools
Browse by area in the simulator list. Every tool page has a worked example and the equations it uses. If you spot a mistake, tell us with the report button on the page or through the contact form.
← NovaSolver home | 日本語 | 中文